SE6035 and SE6075 General Purpose
SILPLUS® Elastomers

PRODUCT DESCRIPTION

SE 6035 and SE 6075 are general purpose Silplus stocks which have durometers of 35 and 70 respectively. They are designed to accept moderate to high levels of reinforcing or extending fillers and additives for property variation. They can also be blended to provide durometers between 35 and 70.

KEY PERFORMANCE PROPERTIES

• Simplicity and accuracy in compounding
• Formulation versatility to achieve end use requirements
• Easily compounded and fabricated using conventional techniques.

TYPICAL PRODUCT DATA
Typical Properties of Uncured Compounds

A = Typical Physical Properties, B = Momentive Performance Materials Quality Control Specs.

Typical Properties of Cured Compound

ADDITIVES

SILPLUS Elastomeric System includes additives to modify the processing and/or cured physical properties of the compounding bases.

Extending Filler Profile of SE6035 and SE6075

Typical Curing Agents

CURING AGENT SUPPLIERS
^1. Trademark of and available from Noury Chemical Corp., Route 78, Burt, New York 14028
^2. Trademark of and available from Lucidol Division, Pennwalt Corporation, 1740 Military Road, Buffalo, New York 14240
^3. Trademark of and available from Hercules Powder Company, 910 Market Street, Wilmington, Delaware 19899
^4. Trademark of and available from R.T. Vanderbilt Company, 30 Winfield Street, E. Norwalk, Connecticut 06855

FABRICATION

Various organic peroxides will vulcanize the compounding bases. Fabricators should make their selection of curing agent on the basis of method of fabrication, desired properties, and safety considerations.

The optimum cure cycle will depend on the method of processing used and the physical dimensions of the vulcanized product. Specific applications will require the use of air oven post cures.

HANDLING AND SAFETY

Material Safety Data Sheets are available upon request from Momentive Performance Materials. Similar information for solvents and other chemicals used with Momentive Performance Materials products should be obtained from your suppliers. When solvents are used, proper safety precautions must be observed.

*CAUTION: 2.4 Dichloro benzoyl peroxide (*Cadox®TS-50) catalyst (Cas#133-14-2) may generate polychlorinated biphenyls during the curing process. Consult Federal REgulations 40 CFR 761 for inadvertent PCB generation regulations.

STORAGE WARRANTY PERIOD

The warranty period is 8 months from date of shipment from Momentive Performance Materials if stored in the original unopened container at 35°C (95°F).

AVAILABILITY

Momentive Performance Materials products may be ordered from Momentive Performance Materials, Waterford, NY 12188, the Momentive Performance Materials sales office nearest you or where appropriate, an authorized Momentive Performance Materials product distributor.

GOVERNMENT REQUIREMENTS

Prior to considering use of a Momentive Performance Materials' product in fulfilling any government requirement, please contact the Government and Trade Compliance office at 413-448-4624.

CDS4802

LEGAL DISCLAIMER

THE MATERIALS, PRODUCTS AND SERVICES OF MOMENTIVE PERFORMANCE MATERIALS, THEIR SUBSIDIARIES OR AFFILIATES (THE “SUPPLIER”), ARE SOLD SUBJECT TO THE SUPPLIER’S STANDARD CONDITIONS OF SALE, WHICH ARE INCLUDED IN APPLICABLE SALES AGREEMENTS, PRINTED ON THE BACK OF ACKNOWLEDGMENTS AND INVOICES, OR AVAILABLE UPON REQUEST. ALTHOUGH THE INFORMATION, RECOMMENDATIONS OR ADVICE CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SUPPLIER MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (I) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (II) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SUPPLIER’S MATERIALS, PRODUCTS, SERVICES, RECOMMENDATIONS OR ADVICE. NOTHING IN THIS OR ANY OTHER DOCUMENT SHALL ALTER, VARY, SUPERSEDE OR OPERATE AS A WAIVER OF ANY OF THE SUPPLIER’S STANDARD CONDITIONS OF SALE.

Each user bears the full responsibility for making its own determination as to the suitability of Supplier’s materials, products, services, recommendations or advice for its own particular purpose. Each user must identify and perform tests and analyses sufficient to assure it that its finished parts will be safe and suitable for use under end-use conditions. Because actual use of products by the user is beyond the control of Supplier, such use is within the exclusive responsibility of the user, and Supplier cannot be held responsible for any loss incurred through incorrect or faulty use of the products. Further, no statement contained herein concerning a possible or suggested use of any material, product, service or design is intended or should be construed to grant any license under any patent or other intellectual property right of Supplier or any of its subsidiaries or affiliated companies, or as a recommendation for the use of such material, product, service or design in the infringement of any patent or other intellectual property right.